The Smart Tek family
Smart Tek structured wiring and network equipment

STRUCTURED WIRING & PRE-WIRE

SMART HOME WIRING.

Structured wiring is the backbone behind a smart home: the network, AV, control, and surveillance camera cable, run right the first time. We pre-wire for homeowners building or renovating on Long Island, and for the builders and designers they work with.

Since 2004SERVING LONG ISLAND
35+ yearsOF FOUNDER EXPERIENCE
Fully insuredON EVERY JOB

OVERVIEW

THE WIRING YOU WON’T SEE, DONE RIGHT.

Smart home wiring goes in once, before the walls close. We plan every drop with you and your builder, pull and label each run, and bring it all back to one equipment location, so the network, TVs, speakers, keypads, shades, and cameras you add later have a clean path to work on.

  • Network cable (Cat6 / Cat6A) to every room
  • Fiber between floors and buildings
  • Coax for TV and antenna
  • In-wall and in-ceiling speaker wire
  • Control, keypad, and touchscreen locations
  • Motorized shade wiring at each window
  • Surveillance camera and doorbell locations
  • Central equipment rack (head-end)
  • Conduit for future runs
THE WIRING YOU WON’T SEE, DONE RIGHT.

CAPABILITIES

WHAT WE PRE-WIRE.

Smart Tek treats each capability as part of a coordinated system, designed, installed, and supported by the same team.

Structured Cabling

Cat6 and Cat6A network cable to TVs, desks, access points, and equipment, with fiber where distance or bandwidth calls for it.

Distributed Audio

Speaker wire to in-wall and in-ceiling locations, plus coax and HDMI paths to every planned TV.

Engraved Keypads

Wire and back boxes at keypad and touchscreen locations, placed where you’ll actually reach for them.

Motorized Shades

Low-voltage or power drops at each window that will get a motorized shade, set before drywall and trim.

Camera & Door Locations

Cable to planned surveillance camera, video doorbell, and intercom locations around the house.

Custom Racks

Every run labeled and brought back to a central rack, with conduit left in place for runs you haven’t planned yet.

WHERE IT LIVES

FROM OPEN STUDS TO A FINISHED RACK.

Real Smart Tek pre-wire and rack work, from a waterfront new build to a finished equipment closet.

New Construction Rough-In

New Construction Rough-In

Cable pulled and staged at each opening while the framing is still open.

Shade & Window Drops

Shade & Window Drops

Shade wiring and tracks set into the structure before finishes go on.

Central Equipment Rack

Central Equipment Rack

Every labeled run lands in one serviceable rack for network, AV, and control.

WHY TIMING MATTERS

WIRE IT BEFORE THE WALLS CLOSE.

Pre-wire happens after framing and before insulation and drywall. At that point a run takes minutes and costs little. After the walls are finished, the same run means opening drywall, patching, and painting, or settling for a wireless device where a cable belonged. Adding a few spare runs and conduit now costs far less than fishing wire later.

PROCESS

HOW SMART TEK DELIVERS IT.

A clear process, from first walkthrough to long-term care.

01

PLAN

Walk the plans with you, your builder, or your designer and mark every TV, speaker, keypad, shade, camera, and access point.

02

ROUGH-IN

Pull and label cable after framing, before insulation and drywall, and coordinate with the electrician and other trades.

03

TRIM-OUT

Terminate and test every run after paint, then build the equipment rack and install devices.

04

DOCUMENT

Leave you with a labeled rack and a record of what was run where, so any future work starts from a clear map.

WHAT'S INCLUDED

NEW CONSTRUCTION OR RENOVATION.

Both start with a site visit. What changes is how we get the cable in.

NEW CONSTRUCTION

Building a new home on Long Island or in the Hamptons.

  • We join early, ideally while plans are still being drawn
  • Rough-in scheduled with your builder after framing
  • Every drop placed before insulation and drywall
  • Rack location planned with the electrician
  • Conduit left for future runs

RENOVATION & RETROFIT

Updating a finished home or gutting part of one.

  • We wire open walls during a renovation
  • In finished rooms we fish cable through existing walls and ceilings
  • Wireless options where a run isn’t practical
  • Older wiring tested and reused where it still works
  • Equipment closet cleaned up or rebuilt

FAQ

FREQUENTLY ASKED.

As early as you can, ideally while the plans are being drawn and before framing is finished. We need to be on site after framing and before insulation and drywall go in.

Yes. We work alongside builders, electricians, architects, and interior designers on new construction and renovations, and schedule our rough-in and trim-out around their timeline.

Often, yes. We fish cable through existing walls and ceilings where we can, and recommend a wireless option where a new run isn’t practical.

Across Long Island, in Suffolk and Nassau, plus the Hamptons and Manhattan.

LET'S BUILD SOMETHING

ONE COMPANY FOR THE
WHOLE HOUSE.

TVs, audio, Wi-Fi, cameras, lighting and shades — designed, installed and supported since 2004.

Book a free site visit, or call 631-656-9180 · Mon–Fri 8 AM–6 PM, Sat 9 AM–1 PM

Smithtown, NY 11787 · Serving Long Island, Manhattan and the Hamptons