The order shade decisions stop being reversible
A window gets built in a fixed order, and every stage of that order takes something off the table. The framing goes up. The window goes in. If anything is going to be hidden inside the ceiling or the head detail, the opening for it is framed now, or not at all. Insulation follows, then drywall, then trim, then paint. Only after that is there a finished opening with real dimensions in it, which is the first moment anyone can measure a shade and expect the number to be true. Measuring is late in that sequence, not early. The decisions that change what gets measured all happen upstream of it, and they close at different times. That is the useful thing to understand about motorized shades, more than any particular fabric or motor.

What the framing closes
A pocket, or recess, is a framed cavity in the ceiling or above the window into which the shade retracts, leaving a narrow slot and nothing else visible. It is the cleanest result available, and it is the least forgiving thing on the list, because it has to be framed to the dimensions of a specific roll of a specific fabric on a specific tube, with service access built in for later. A pocket framed to a guess frequently does not fit the shade that gets chosen months after the guess.
Which means the hidden-shade decision is not really a shade decision at all at that point in the job. It is a carpentry decision being made before the shade exists, and it requires the shade type and fabric to be pinned down earlier than homeowners naturally want to pin anything down. Once the ceiling is closed and skimmed, what remains available is a surface-mounted shade with a fascia or cover over the roll. That can look well resolved. It is never invisible.
What the rough-in closes
Low-voltage wire to each window is close to free while the stud bays are open and the electrician is already on site; the labor is in being there. After insulation and drywall it becomes a cut-and-fish job with patching and painting behind it, which is why houses that were not wired for shades rarely get wired for shades later.
Batteries are the answer to a closed wall, and they are a legitimate answer rather than a compromise. The thing that distinguishes a good battery decision from a bad one is reach. A shade a person can get to from a step stool is a small maintenance item. A shade over a two-story window, above a stair, or behind a built-in is a tall-ladder event or a service call every time the batteries come due. The relevant information — how long a given shade runs on a set of batteries — is published per model on the Lutron specification sheet for that shade, not available as a rule of thumb, and it varies with how often the shade is asked to move.
So the power question resolves window by window rather than house-wide, sorted by how hard that particular shade will be to reach in several years. Mixed installations are normal: wire where the wire is practical or the window is high, batteries where it is not.
What the window itself closes
Third is mount type, and this one was decided by whoever set the window and the trim, before anybody was thinking about shades.
An inside mount sits within the opening. It keeps the trim visible and reads as part of the window, and it needs depth in the opening for the roll and the brackets — a depth that differs by shade model — plus an opening square enough for the fabric to hang parallel to the jamb. A shallow or out-of-square opening does not forbid an inside mount so much as it guarantees the result will look like a compromise.
An outside mount sits on the trim or the wall above. It needs flat surface and clearance from whatever else is up there: casement cranks, door hardware, a supply register. It covers the edges of the opening, blocks more light, and tolerates openings that an inside mount cannot.
The detail nobody checks until the shade is hanging: an inside mount always leaves a gap at each side, because the fabric cannot run to the jamb without rubbing it. For most rooms that gap is irrelevant. For a bedroom or a media room where somebody expects real darkness, it is the whole problem, and the fix is either an outside mount or side channels, both of which are decisions, not adjustments.
What stays open the longest
Fabric stays open until the order goes in, and it stays open for a reason: nothing structural depends on it except the pocket.
Openness is the share of the weave that is actually open — stated as a percentage on the fabric specification — and it sets how much light and how much view get through. Lower openness cuts more glare and shows less outside. Higher openness keeps the view and lets more light in.
Color does as much work as openness, and it works in the direction people do not predict. A pale fabric scatters sunlight forward off every thread, so the fabric itself lights up and becomes a bright veil hanging between the room and the outside; the view goes hazy and the glare moves rather than leaves. A dark fabric absorbs more of what hits it and stays dim, so the eye looks through the weave instead of at it, and the view holds. A pale, very open fabric can still put a bright reflection on a television.
Nighttime runs the other way entirely. With the lights on inside, most open-weave fabric lets people outside see in — the bright side is now the room. Where that matters, the answer is a room-darkening or privacy fabric, or a second shade on the same window, and the second shade is another thing the pocket has to have been sized for.
Where control belongs in the sequence
Control does not change a single dimension on a measurement sheet, which is why it tends to get deferred, and deferring it is the mistake.
Keypads, remotes, app control, schedules, and shades joined into lighting scenes all behave differently at the planning stage. The ones that live on a wall need a box in that wall, and the box needs to exist before the drywall does. A shade that is going to answer to a bedside keypad has a wiring requirement that has nothing to do with the shade and everything to do with where somebody sleeps.
What the sequence reveals
Set against each other, the stages tell a consistent story: the irreversible choices get made first, by trades who are not thinking about shades, and the reversible ones get made last, by the people who care most about them.
That is the inversion worth knowing. Fabric, openness, scene levels and schedules — the decisions homeowners deliberate hardest over — are the ones that stay available, and several of them get revised after a season of living with the house. Pocket framing, wire in the wall and keypad boxes are the decisions nobody deliberates over at all, because they come up in the middle of a construction schedule as a yes-or-no question from a contractor who needs an answer that morning.
The cost of getting the late decisions wrong is a reorder. The cost of getting the early ones wrong is drywall, paint, and a shade hanging below a ceiling it was supposed to disappear into.
FAQ
Frequently asked questions
Neither is better in the abstract; the opening decides. An inside mount keeps the trim visible and needs depth for the roll and brackets, plus an opening square enough for the fabric to hang parallel to the jamb. An outside mount tolerates shallow or out-of-square openings and covers the edges, which blocks more light at the cost of sitting proud of the trim.
Yes, and it is the normal path in a house that was never wired for them. Battery power, surface mounting and wireless control make it routine. What is off the table is the hidden pocket and hardwired power at every window, because both of those were settled while the ceiling was open.
It is the share of the weave that is open, and it sets the balance between how much light and glare pass through and how much of the view survives. Lower openness cuts more glare and shows less outside. Fabric color pulls on the same result, since a pale weave scatters sunlight forward and becomes a bright veil while a dark one absorbs more and lets the eye read through it.
A pocket is framed structure, sized to a specific roll of a specific fabric, with service access designed into it. Adding one later means opening and reframing a finished ceiling or head detail. The surface-mounted alternative with a fascia can look well resolved, but the roll is still in the room.
Plan the shades
For shade selection, control and scenes, see Lighting & Shade Control. For power and cabling during a renovation or new build, see Smart Home Wiring & Pre-Wire.
Our town guides for Lloyd Harbor and Sagaponack cover shades in houses with a lot of glass.
Talk through the problem
Call 631-656-9180, Mon–Fri 8 AM–6 PM and Sat 9 AM–1 PM, or tell us what is happening through the contact form. We serve Long Island, Manhattan and the Hamptons.
